imaging failed to proceed around 26%
imaging failed to proceed around 26%
Hello there,
I have a 32G RevPi Connect+ on which I was trying to load the 2022 05 25 revpi buster image through the win32diskimager, but kept failing around 25%.
power reset didn't help either and screen capture uploaded as blow:
would you help to figure out what the problem is pls?
I have a 32G RevPi Connect+ on which I was trying to load the 2022 05 25 revpi buster image through the win32diskimager, but kept failing around 25%.
power reset didn't help either and screen capture uploaded as blow:
would you help to figure out what the problem is pls?
- Attachments
-
- revpi_imaging_failure.png (28.94 KiB) Viewed 5277 times
Re: imaging failed to proceed around 26%
Maybe the wire, which disables the hardware watchdog is missing on connector X4?
-Nicolai
-Nicolai
Re: imaging failed to proceed around 26%
nicolaiB wrote: ↑06 Oct 2022, 11:27 Maybe the wire, which disables the hardware watchdog is missing on connector X4?
For more Information see here https://revolutionpi.com/tutorials/uebe ... g-connect/
Best Regards
Ulrich Kouatang Biakoup | Technical Support
Re: imaging failed to proceed around 26%
jumper cable is in as pic shows.
and with this same cable I have imaged the other one, on the left side in picture for many times, no any issue with it
and with this same cable I have imaged the other one, on the left side in picture for many times, no any issue with it
- Attachments
-
- repvi_imaging.png (346.59 KiB) Viewed 5219 times
Re: imaging failed to proceed around 26%
Hallo Kwang,
I have some instructions for you.
Please use the software balenaEtcher instead of Win32DiskImager.
https://www.balena.io/etcher/
We have a new Image from 08/2022 on our homepage. You can fash it on your Device: https://revolutionpi.de/tutorials/downloads/
Maybe make sure you are using anew version of RPI Boot.
We have a Revolution Pi RPI Boot Checklist
Best Regards
Ulrich Kouatang Biakoup | Technical Support
I have some instructions for you.
Please use the software balenaEtcher instead of Win32DiskImager.
https://www.balena.io/etcher/
We have a new Image from 08/2022 on our homepage. You can fash it on your Device: https://revolutionpi.de/tutorials/downloads/
Maybe make sure you are using anew version of RPI Boot.
We have a Revolution Pi RPI Boot Checklist
Best Regards
Ulrich Kouatang Biakoup | Technical Support
Re: imaging failed to proceed around 26%
balena didn't work either.
any idea about the root cause?
any idea about the root cause?
Re: imaging failed to proceed around 26%
Hello Kwang,
Have you tried with another wire?
The same problem occurs when the wire is nit stable or defective.
please try with another wire.
Best Regards
Ulrich Kouatang Biakoup | Technical Support
Have you tried with another wire?
The same problem occurs when the wire is nit stable or defective.
please try with another wire.
Best Regards
Ulrich Kouatang Biakoup | Technical Support
Re: imaging failed to proceed around 26%
tried with diffrent usb cables, power reset my pc, etc.
Re: imaging failed to proceed around 26%
Hi Kwang,
Could you try with another pc? If the problem is RPI-BOOT. Please have a look on Revpi Boot checklist.
Best Regards
Ulrich Kouatang Biakoup | Technical Support
Could you try with another pc? If the problem is RPI-BOOT. Please have a look on Revpi Boot checklist.
Best Regards
Ulrich Kouatang Biakoup | Technical Support