Hi, meine Empfehlung - verwende REVPIPYLOAD, dann funktioniert es ganz simpel siehe hier
https://revpimodio.org/revpipyplc/revpipyload/
Search found 1918 matches
- 19 Mar 2024, 12:41
- Forum: Software
- Topic: automatischer Start des Python Programms
- Replies: 4
- Views: 977
- 18 Mar 2024, 14:58
- Forum: RevPi Nodes for Node-RED
- Topic: Newbe question about RevPi Connect 4
- Replies: 3
- Views: 2018
Re: Newbe question about RevPi Connect 4
Hi Gabriele, have a look here at the documentation - it is called "RevPiStatus" at Bit 6:
https://revolutionpi.com/en/tutorials/s ... pi-connect Thus, you can configure this input in Node-RED as follows:
https://revolutionpi.com/en/tutorials/s ... pi-connect Thus, you can configure this input in Node-RED as follows:
- 18 Mar 2024, 14:51
- Forum: Software
- Topic: Änderung beim Depot?
- Replies: 5
- Views: 2270
Re: Änderung beim Depot?
Hallo Ingo, das sieht erst mal seltsam aus. Kannst Du mir einen SOS-Report schicken? Kannst Du sagen, seit wann der Fehler besteht bzw. ob etwas geändert wurde dass den Fehler verursacht haben kann?
- 18 Mar 2024, 14:15
- Forum: Software
- Topic: Node Red Won't launch
- Replies: 11
- Views: 47607
Re: Node Red Won't launch
Hi DarylDominique, thank you for your positive feedback and the solution to the problem.
- 18 Mar 2024, 14:12
- Forum: Hardware
- Topic: RevPi Connect SE Sensor Connection
- Replies: 3
- Views: 2542
Re: RevPi Connect SE Sensor Connection
Hi user123, can you say what might have changed since the Modbus communication stopped working? Can you say what is in the status registers? https://revolutionpi.com/en/tutorials/modbus-tutorial/revpi-compact-als-modbus-rtu-master-verwenden?noredirect=en-US Here is a troubleshooting that is related ...
- 18 Mar 2024, 14:06
- Forum: CODESYS
- Topic: CodeSys OPC UA Server - keine Verbindung von entferntem Netzwerk
- Replies: 4
- Views: 462
Re: CodeSys OPC UA Server - keine Verbindung von entferntem Netzwerk
Hi beusterh, danke für Deine positive Rückmeldung und die Lösung hierfür, das ist klasse!
- 18 Mar 2024, 13:37
- Forum: Hardware
- Topic: " Module not present" even though connected
- Replies: 3
- Views: 2417
Re: " Module not present" even though connected
Hi Ajinkya09, this is unfortunately our drama queen PiCtory ... If it's not all just like it should be then here it goes :roll: Just swap the DIO Module in PiCtory as follows - you have to click on the animated GIF for animation ... next drama ... Don't forget to save and reset the driver ;) chrome_...
- 18 Mar 2024, 09:08
- Forum: Software
- Topic: Reset Login Password
- Replies: 1
- Views: 859
Re: Reset Login Password
Hi Vela1001, this is the more or less new authentication dialogue from CODESYS.
Take a look here at our knowledge base, there is a step where you can watch a little video: Commissioning Modular Gateway EtherCAT with CODESYS -> “Go online for the first time”.
Take a look here at our knowledge base, there is a step where you can watch a little video: Commissioning Modular Gateway EtherCAT with CODESYS -> “Go online for the first time”.
- 15 Mar 2024, 11:03
- Forum: Connectivity
- Topic: Serielles USB Gerät wird nicht erkannt
- Replies: 3
- Views: 2370
Re: Serielles USB Gerät wird nicht erkannt
Hi smon, also erstmal danke für die ausführliche Schilderung des Fehlerbildes. Bedeutet „in den zweiten USB-Port des RevPis stecke“ dass die beiden USB Gerät an zwei verschiedene Ports gesteckt wurden? Verwendest Du ein Netzteil > 11V? Ich weiß das hört sich erst einmal seltsam an jedoch steht im Da...
- 12 Mar 2024, 12:20
- Forum: Hardware
- Topic: RevPi not responding after re-imaging
- Replies: 1
- Views: 757
Re: RevPi not responding after re-imaging
Hi jonaswiberg, you can use a tool that writes and reads out the written image to prove that the eMMC is written correct. For example, you can use balena Etcher for this. Then, if the problem persists, you can use an HDMI monitor and a USB keyboard to check for erroneous behavior during boot and try...