Hi Dirk,
Is there any updates on this?
Regards,
Creighton
Search found 9 matches
- 03 Dec 2019, 03:25
- Forum: Software
- Topic: How to pass values from RevPi7 to Modbus TCP
- Replies: 3
- Views: 4581
- 08 Nov 2019, 03:53
- Forum: Software
- Topic: How to pass values from RevPi7 to Modbus TCP
- Replies: 3
- Views: 4581
How to pass values from RevPi7 to Modbus TCP
Hi,
I am able to receive values from my s71200 by using RevPi7 . How do I pass these values to Modbus TCP?
Is it possible to pass the values from RevPi7 to any of the virtual modules provided in Pictory?
Hope to receive some feedback regarding this matter. Thank you.
Best regards,
Creighton
I am able to receive values from my s71200 by using RevPi7 . How do I pass these values to Modbus TCP?
Is it possible to pass the values from RevPi7 to any of the virtual modules provided in Pictory?
Hope to receive some feedback regarding this matter. Thank you.
Best regards,
Creighton
- 17 Oct 2019, 05:11
- Forum: Software
- Topic: Communication with S7-1200
- Replies: 8
- Views: 12204
Re: Communication with S7-1200
Hi, I am also trying to do the same. May I know are you able to receive the values from the PLC and read it by using the Modbus module? I have already programmed the PLC s71200 and assigned a DB. Can you show me an overview on how to configure the revpi 7 to establish a connection with the PLC? I kn...
- 13 Sep 2019, 12:05
- Forum: Hardware
- Topic: Cannot output monitor display
- Replies: 3
- Views: 4805
Re: Cannot output monitor display
Hi Dirk,
Thank you for your solutions. I tried writing my original image into the device which I have backed up earlier and it is working now.
Thank you.
Regards,
Creighton
Thank you for your solutions. I tried writing my original image into the device which I have backed up earlier and it is working now.
Thank you.
Regards,
Creighton
- 11 Sep 2019, 09:01
- Forum: Hardware
- Topic: Cannot output monitor display
- Replies: 3
- Views: 4805
Cannot output monitor display
Hi, The RevPi was working normally until when I rebooted using the terminal by typing "sudo reboot". The problem that occurred is that my monitor stops receiving hdmi signal from the RevPi. Therefore, I cannot see any output displayed in my monitor at all. I have tried to access the config...
- 24 Jul 2019, 04:36
- Forum: Software
- Topic: Revolution Pi Booting Failure
- Replies: 8
- Views: 10619
Re: Revolution Pi Booting Failure
Hi Amar, Thank you for your time and suggested solutions. By the way, I have repeated the whole process again by writing the stretch image to the RevPi by using Win32DiskImager. Before I did that, I only used the SD Card Formatter to overwrite format my RevPi so that I can write the image to it. Aft...
- 22 Jul 2019, 08:31
- Forum: Software
- Topic: Revolution Pi Booting Failure
- Replies: 8
- Views: 10619
Re: Revolution Pi Booting Failure
Hi Amar, As I was done writing the image and started booting the RevPi, the same problem occurred with the last kernel message showing: "[ 1.6152451 ---[ end Kernel Panic - not syncing: VFS: Unable to mount root fs on unknown block(179,2) ]----. I have no cables connected to my RevPi except the...
- 10 Jul 2019, 03:03
- Forum: Software
- Topic: Revolution Pi Booting Failure
- Replies: 8
- Views: 10619
Re: Revolution Pi Booting Failure
Hi Dirk, Thank you for getting back to me. After writing the stretch image in my RevPi Connect, when I start it, it does not bring me to any login screen, it is black screen that just ran a few program lines and stop there as if it has stopped. May I know how to attach image as a reference to my iss...
- 09 Jul 2019, 05:30
- Forum: Software
- Topic: Revolution Pi Booting Failure
- Replies: 8
- Views: 10619
Revolution Pi Booting Failure
Hi, I am facing some issue in booting the KUNBUS Revolution Pi that we recently purchased. I have performed the following steps to configure the Rev Pi and the following errors produced accordingly. 1) I have followed this tutorial 01- Creation of Image, https://revolution.kunbus.com/tutorials/video...